Man pages sections > man3 > App::Pinto::Command::pull

App::Pinto::Command::pull - pull archives from upstream repositories

App::Pinto::Command::pull(3pm) User Contributed Perl Documentation App::Pinto::Command::pull(3pm)

NAME

App::Pinto::Command::pull - pull archives from upstream repositories

VERSION

version 0.097

SYNOPSIS

  pinto --root=REPOSITORY_ROOT pull [OPTIONS] TARGET ...

DESCRIPTION

This command locates packages in your upstream repositories and then pulls the distributions providing those packages into your repository and registers them on a stack. Then it recursively locates and pulls all the distributions that are necessary to satisfy their prerequisites. You can also request to directly pull particular distributions.
When locating packages, Pinto first looks at the packages that already exist in the local repository, then Pinto looks at the packages that are available on the upstream repositories.

COMMAND ARGUMENTS

Arguments are the targets that you want to pull. Targets can be specified as packages (with or without a minimum version number) or a distributions. For example:
  Foo::Bar                                 # Pulls any version of Foo::Bar
  Foo::Bar~1.2                             # Pulls Foo::Bar 1.2 or higher
  SHAKESPEARE/King-Lear-1.2.tar.gz         # Pulls a specific distribuion
  SHAKESPEARE/tragedies/Hamlet-4.2.tar.gz  # Ditto, but from a subdirectory
You can also pipe arguments to this command over STDIN. In that case, blank lines and lines that look like comments (i.e. starting with "#" or ';') will be ignored.

COMMAND OPTIONS

--cascade
!! THIS OPTION IS EXPERIMENTAL !!
 
When searching for a package (or one of its prerequisites), always take the latest satisfactory version of the package found amongst all the upstream repositories, rather than just taking the first satisfactory version that is found. Remember that Pinto only searches the upstream repositories when the local repository does not already contain a satisfactory version of the package.
--dry-run
Go through all the motions, but do not actually commit any changes to the repository. Use this option to see how upgrades would potentially impact the stack.
--no-fail
!! THIS OPTION IS EXPERIMENTAL !!
 
Normally, failure to pull a target (or its prerequisites) causes the command to immediately abort and rollback the changes to the repository. But if "--no-fail" is set, then only the changes caused by the failed target (and its prerequisites) will be rolled back and the command will continue processing the remaining targets.
 
This option is useful if you want to throw a list of targets into a repository and see which ones are problematic. Once you've fixed the broken ones, you can throw the whole list at the repository again.
--recurse
--no-recurse
Recursively pull any distributions required to satisfy prerequisites for the targets. The default value for this option can be configured in the pinto.ini configuration file for the repository (it is usually set to 1). To disable recursion, use "--no-recurse".
--message=TEXT
-m TEXT
Use TEXT as the revision history log message. If you do not use the "--message" option or the "--use-default-message" option, then you will be prompted to enter the message via your text editor. Use the "EDITOR" or "VISUAL" environment variables to control which editor is used. A log message is not required whenever the "--dry-run" option is set, or if the action did not yield any changes to the repository.
--pin
Pins the packages to the stack, so they cannot be changed until you unpin them. Only the packages in the requested targets will be pinned -- packages in prerequisites will not be pinned. However, you may pin them separately with the pin command if you so desire.
--stack=NAME
-s NAME
Puts all the packages onto the stack with the given NAME. Defaults to the name of whichever stack is currently marked as the default stack. Use the stacks command to see the stacks in the repository.
--use-default-message
-M
Use the default value for the revision history log message. Pinto will generate a semi-informative log message just based on the command and its arguments. If you set an explicit message with "--message", the "--use-default-message" option will be silently ignored.
--with-development-prerequisites
--wd
Also pull development prerequisites so you'll have everything you need to work on those distributions, in the event that you need to patch them in the future. Be aware that most distributions do not actually declare their development prerequisites.

AUTHOR

Jeffrey Ryan Thalhammer <jeff@stratopan.com> This software is copyright (c) 2013 by Jeffrey Ryan Thalhammer.
This is free software; you can redistribute it and/or modify it under the same terms as the Perl 5 programming language system itself.
2015-05-29 perl v5.20.2