Man pages sections > man8 > divaload

divaload - configure Eicon Diva active ISDN card

DIVALOAD(8) Linux System Administration DIVALOAD(8)

NAME

divaload - configure Eicon Diva active ISDN card

SYNOPSIS

divaload controller protocol [options]

DESCRIPTION

divaload is used to setup the Eicon Diva card for the proper configuration.

OPTIONS

controller
selects the controller (card). This can be either:
 
-c n
 
where n is the controller number, or
 
-all
 
to operate on all cards.
 
protocol
can be one of the following:
  -f 1TR6     Germany, old protocol for PABX................ PRI & BRI
  -f ETSI     DSS1, Europe (Germany, ...)................... PRI & BRI
  -f FRANC    VN3, France, old protocol for PABX............ PRI & BRI
  -f BELG     NET3, Belgien, old protocol for PABX.......... PRI & BRI
  -f SWED     DSS1 with CRC4 off, Sweden, Benelux........... PRI
  -f NI       NI1, NI2, North America, National ISDN........ PRI & BRI
  -f 5ESS     5ESS, North America, AT&T..................... PRI & BRI
  -f JAPAN    Japan, INS-NET64.............................. PRI & BRI
  -f ATEL     ATEL, Australia, old TPH1962.................. PRI & BRI
  -f US       North America, Auto Detect....................       BRI
  -f ITALY    DSS1, Italy................................... PRI & BRI
  -f TWAN     DSS1, Taiwan.................................. PRI & BRI
  -f AUSTRAL  Australia, Microlink (TPH1962), On Ramp ETSI.. PRI & BRI
  -f 4ESS_SDN 4ESS Software Defined Network................. PRI
  -f 4ESS_SDS 4ESS Switched Digital Service................. PRI
  -f 4ESS_LDS 4ESS Long Distance Service.................... PRI
  -f 4ESS_MGC 4ESS Megacom.................................. PRI
  -f 4ESS_MGI 4ESS Megacom International.................... PRI
  -f HONGKONG Hongkong...................................... PRI & BRI
  -f RBSCAS   Robbed Bit Signaling, CAS..................... PRI
  -f QSIG     QSIG, Intra PABX link protocol................ PRI & BRI
    
 
The following options may be given to divaload.
-e [1,2,3]
set Layer 1 framing on PRI Adapter
1 - doubleframing (NO CRC4)
 
2 - multiframing (CRC4)
 
3 - autodetection
-x
set PRI Adapter in NT mode; default mode is TE
-z
set PRI Adapter in High Impedance state until first user application does request interface activation
-l [1...30]
set starting channel number on PRI Adapter. By default the allocation of channels is made on a high-to-low basis. By specifying -l you select a low-to-high allocation policy (in addition)
-q [0..3]
select QSIG options
0 - CR and CHI 2 Bytes long (default)
 
1 - CR 1 byte, CHI 2 bytes
 
2 - CR is 2 bytes, CHI is 1 byte
 
3 - CR and CHI 1 byte
 
(CR - Call Reference, CHI - B-Channel Ident.)
-n [0...20]
select NT2 mode and default length of DIDN (DIDN - Direct Inward Dial Number)
-o
turn off order checking of information elements
-p [1,2]
establish a permanent connection (e.g. leased line configuration)
1 - TE <-> TE mode, structured line
 
2 - NT <-> TE mode, raw line
-s [0,1,2,3]
D-Channel Layer 2 activation policy on BRI Adapter
0 - On demand
 
1 - Deactivation only by NT side, preferred, default
 
2 - Always active
 
3 - Always active, mode 2
 
-t [0...63]
specifies a fixed TEI value (Default is a automatic TEI assignment)
 
-u
select point to point mode on BRI Adapter; uses default TEI '0', NT2 mode is on
 
-[1...8]oad|osa|spid
BRI Adapter B-Channel options Specify the Originating Address (OAD), Originating Sub-address (OSA) and/or Service Profile Identifier (SPID) for each B-channel (1 or 2 by BRI, 1...8 by 4BRI)
 
Example: -1oad 123456 -1spid 1234560001
 
-d
display protocol options summary
 
-w
select alternative protocol code directory.
 
default directory: "/usr/share/isdn"
 
-h or -?
help
 
 

AUTHOR

manpage written from -h output by Paul Slootman <paul@debian.org>.
2000/12/02 divaload