isadump - examine ISA registers
] [-k V1,V2...
]] #for I2C-like
]]] #for flat address space
isadump is a small helper program to examine registers visible through the ISA
bus. It is intended to probe any chip that lives on the ISA bus working with
an address register and a data register (I2C-like access) or a flat range (of
up to 256 bytes).
- Enable flat address space mode.
- Disable interactive mode. By default, isadump will wait for
a confirmation from the user before messing with the ISA bus. When this
flag is used, it will perform the operation directly. This is mainly meant
to be used in scripts.
- -k V1,V2...
- Specify a comma-separated list of bytes to send as the key
sequence to enter the chip configuration mode. Most Super-I/O chips need
this. Known key sequences are: 0x87,0x01,0x55,0x55 for ITE, 0x55 for SMSC,
0x87,0x87 for Winbond and VIA, none needed for National
- Perform 16-bit reads.
- Perform 32-bit reads.
At least two options must be provided to isadump. addrreg
ISA address of the address register for the chip to probe; datareg
contains the address of the data register. Both addresses are integers between
0x0000 and 0x3FFF. Usually, if the chip's base address is 0x0nn0, the address
register is at 0x0nn5 and the data register is at 0x0nn6. The most common base
address for hardware monitoring chips is 0x0290.
For Super-I/O chips, address register is typically at 0x2E with data register at
parameters are useful on the Winbond chips as
well as on Super-I/O chips. bank
is an integer between 0 and 31, and
is an integer between 0x00 and 0xFF (default value: 0x4E for
Winbond chips, 0x07 for Super-I/O chips). The W83781D datasheet has more
information on bank selection.
In flat mode, only one parameter is mandatory. address
contains the ISA
address of the chip to probe; it is an integer between 0x0000 and 0xFFFF. If
is how many bytes should be read (must be a multiple of
16). If the range isn't provided, it defaults to 256 bytes and the address is
forcibly aligned on a 256-byte boundary.
parameters are useful on the National
Semiconductor PC87365 and PC87366 Super-I/O chips. bank
is an integer
between 0 and 31, and bankreg
is an integer between 0x00 and 0xFF
(default value: 0x09; must fit in the specified range). See the PC87365
datasheet for more information on bank selection.
If no bank is specified, no bank change operation is performed.
If a bank is specified, the original value is restored before isadump exits.
Dumping Super-I/O chips is typically a two-step process. First, you will have to
access the main Super-I/O address using a command like: isadump 0x2e 0x2f
0x09. This will select logical device 9 (correct value depend on the chip). At
0x60 you will find the logical device address word, for example "ec
c0". Then you can use a command like: isadump -f 0xecc0 16. This will
dump the logical device registers. The correct range depends on the chip.
Poking around in ISA data space is extremely dangerous. Running isadump with
random parameters can cause system crashes, data loss, and worse! Be extremely
careful when using this program.
Frodo Looijaard, Mark D. Studebaker, and the lm_sensors group
This manual page was originally written by David Z Maze <email@example.com>
for the Debian GNU/Linux system. It was then reviewed and augmented by the
lm_sensors team and is now part of the lm_sensors source distribution.