URONode - Node front end for AX.25, NET/ROM, Rose and TCP
is a simple node front end, modelled after the node shells of
LinuxNode, AWZNode, and Flexnode.
The following commands are supported for users of URONode:
- Give short list of available commands.
- Reads the file uronode.announce. This is like a local
announcement wall where you can give your locals connecting into your node
a chance to see the local activities going on like a cork board with
- Disconnect user from the node.
- Connect <call | alias> [s|d] For NETROM
- Connect <port> <call> [via <call1>
...] [d|s] For AX.25
- Connect <call> <address> [<digi>]
[d|s] For ROSE
- Connect <destination> [s|d] For FlexNet
Initiates an AX25, NET/ROM, ROSE or Flexnet connection to a remote host. If
more than two parameters are entered and the second parameter is ten
charachers in length then it is interpreted as a ROSE connection,
otherwise the first parameter is interpreted as a port name and AX25 is
used to make the connection via that port. If only one parameter is given
the connection is made searching for the callsign in NET/ROM nodes, in
AX25 Fixed links, in FlexNet destinations and last in Mheard database in
For a ROSE connection the <address> part must be exactly six or ten
digits. If only six digits are supplied, the DNIC (first four digits)
default to the local DNIC. The local DNIC is assumed to be that of the
first configured Rose port in /etc/ax25/rsports.
The user may optionally supply as the last argument a single character which
modifies the default behaviour on disconnection of the connection. If a
single `s' is entered as the last argument, then when the remote host
disconnects you will be returned to this node. If a single `d' is entered
as the last argument, you will be disconnected from this node too. The
Default behaviour (neither `s' nor `d' entered) is configured in the node
configuration file and depends on the sysop preference.
- CAllbook <call>[@<server>]
- Retrieve data about a callsign from an internet-accessible
callbook server. The server name can usually be omitted, since the default
server configured by the operator is usually valid. The default setting
can be overridden by specifying a host name.
- Escape [<escape string>]
- Override the sysop configured default escape character
setting. If the Escape command is given without an argument then the
current escape character setting is returned to the user. The escape
string may be specified using any of the well known codings:
- <char> to enter the escape character in its
- ^C to enter the escape character as a control
- NNN to set the escape character to a Decimal
- 0xNN to set the escape character to a HexaDecimal
- 0NNN to set the escape character to an Octal
- off to disable the escape character.
- Finger [<username>][@<hostname>]
- Retrieve information about users of a system. If the user
name is omitted, shows the users currently logged on the host. If the
hostname is omitted, defaults to the local host.
- Help [<command>]
- Give help for the specified command or this text if no
command is specified. Commands can not be abbreviated. Use the
"?" command to retrieve a list of available commands.
- HOst <hostname> | <ip address>
- Give the Domain Name Service host name information about
<hostname> or <ip address>.
- Display the version information and the contents of the
/usr/local/etc/ax25/uronode.info file, which should describe any aspects
of your system that you would like to brag about.
- Display the node's interface schema, most folks often call
- Displays the last 20 stations heard to this node. You may
use an interface name to get the last 20 stations heard to that particular
- Displays the full list of the heards database up to the
last 100 callsigns. Add the name of an interface for the full heards
listing for that specific interface.
- Links [d | n | v | <call>]
- Shows the AX25 link table of the local node. The
destinations on this list can be reached using the Connect command without
knowing the actual network path used (assuming the network is OK).
The optional parameter d show the AX25 nodes directly linked. The optional
parameter n show the AX25 nodes linked connecting another node and passing
a string like "C XX0XX". The optional parameter v show the AX25
links via digipeaters.
You can also specify a destination callsign to get the verbose information
for a single destination.
- Nodes [* | <node>]
- Show the NET/ROM node table of the local host. The nodes on
this list can be reached using the Connect command without knowing the
actual network path used (assuming the network is OK).
The optional argument '*' toggles verbose mode, showing the Obsolescence
counter, relative path quality and the port and neighbour node used to
reach each node. You can also specify a node callsign to get the verbose
information for a single node. In that case a "which" field that
tells what route the kernel will use to reach the node is also shown.
- Ping <host> [<size>]
- Check if a host can be reached trough the network by
sending an ICMP Echo Request packet to the host and waiting for it to
reply. If a reply is received the round-trip-time (RTT) between the local
and remote hosts is shown.
If an optional length is specified the data portion of the packet is filled
with length number of bytes up to 128.
- Shows the NET/ROM route table of the local host (eg. the
nodes which the local node directly talks with). These nodes are used to
reach the other nodes on the node table. Fields shown are:
- Link Is there an AX25 connection active to this
- Port Which port is this route on.
- Callsign The callsign of the neighbour node.
- Quality A relative quality for the path
- Destinations Number of other nodes reached via this
- Lock Is the quality of this route locked by the
- QSO Number of NET/ROM session enties.
- Telnet <host> [<port>] [<string>]
- Initiate a telnet session to a remote host using TCP/IP. By
default, the telnet command connects to the TCP port 23 (allocated for
telnet). You can specify another TCP port or a TCP port name.
If an optional third argument <string> is given, that string, followed
by a CRLF is sent to the remote host right after the connection is
established. This is mainly useful for command aliases.
If a single `s' is entered as the last parameter, then when the remote host
disconnects you will be returned to this node. If a single `d' is entered
as the last parameter, you will be disconnected from this node too.
Default behaviour (neither `s' nor `d' entered) depends on sysop
- MSG <user> <message>
- Send a message to another user of the node. The user in
question must be in idle state (ie. not connected/connecting anywhere or
running a program).
If the user has an SSID other than zero, the SSID must be specified. If
multiple users are logged in with the same callsign/SSID pair, those who
are in idle state, get the message.
- Show a list of users currently connected to the local node,
where the users are coming from, and what are they doing at the
- URONode configuration file.
- URONode permissions file.
- URONode users settings file.
- URONode message of the day file.
- The response to the 'info' command. This file should be
edited to reflect the local configuration.
- Database of current users.
- Information about AX.25 stations heard.
- The online help files.
Brian Rogers N1URO <firstname.lastname@example.org>
Stefano Noferi IZ5AWZ <email@example.com>
Tomi Manninen OH2BNS <firstname.lastname@example.org>
Alan Cox GW4PTS <email@example.com>
Roy PE1RJA <firstname.lastname@example.org>