Man pages sections > man8 > wg-quick

wg-quick - set up a WireGuard interface simply

WG-QUICK(8) WireGuard WG-QUICK(8)


wg-quick - set up a WireGuard interface simply


wg-quick [ up | down ] [ CONFIG_FILE | INTERFACE ]


This is an extremely simple script for easily bringing up a WireGuard interface, suitable for a few common use cases.
Use up to add and set up an interface, and use down to tear down and remove an interface. Running up adds a WireGuard interface, brings up the interface with the supplied IP addresses, sets up mtu and routes, and optionally runs pre/post up scripts. Running down optionally saves the current configuration, removes the WireGuard interface, and optionally runs pre/post down scripts.
CONFIG_FILE is a configuration file, whose filename is the interface name followed by `.conf'. Otherwise, INTERFACE is an interface name, with configuration found at `/etc/wireguard/ INTERFACE.conf'.
Generally speaking, this utility is just a simple script that wraps invocations to wg(8) and ip(8) in order to set up a WireGuard interface. It is designed for users with simple needs, and users with more advanced needs are highly encouraged to use a more specific tool, a more complete network manager, or otherwise just use wg(8) and ip(8), as usual.


The configuration file adds a few extra configuration values to the format understood by wg(8) in order to configure additional attribute of an interface. It handles the values that it understands, and then it passes the remaining ones directly to wg(8) for further processing.
It infers all routes from the list of peers' allowed IPs, and automatically adds them to the system routing table. If one of those routes is the default route ( or ::/0), then it uses ip-rule(8) to handle overriding of the default gateway.
The configuration file will be passed directly to wg(8)'s `setconf' sub-command, with the exception of the following additions to the Interface section, which are handled by this tool:
Address — a comma-separated list of IP (v4 or v6) addresses (optionally with CIDR masks) to be assigned to the interface. May be specified multiple times.
DNS — a comma-separated list of IP (v4 or v6) addresses to be set as the interface's DNS servers. May be specified multiple times. Upon bringing the interface up, this runs `resolvconf -a tun. INTERFACE -m 0 -x` and upon bringing it down, this runs `resolvconf -d tun. INTERFACE`. If these particular invocations of resolvconf(8) are undesirable, the PostUp and PostDown keys below may be used instead.
MTU — if not specified, the MTU is automatically determined from the endpoint addresses or the system default route, which is usually a sane choice. However, to manually specify an MTU to override this automatic discovery, this value may be specified explicitly.
PreUp, PostUp, PreDown, PostDown — script snippets which will be executed by bash(1) before/after setting up/tearing down the interface, most commonly used to configure custom DNS options or firewall rules. The special string `%i' is expanded to INTERFACE.
SaveConfig — if set to `true', the configuration is saved from the current state of the interface upon shutdown.
Recommended INTERFACE names include `wg0' or `wgvpn0' or even `wgmgmtlan0'. However, the number at the end is in fact optional, and really any free-form string [a-zA-Z0-9_=+.-]{1,16} will work. So even interface names corresponding to geographic locations would suffice, such as `cincinnati', `nyc', or `paris', if that's somehow desirable.


These examples draw on the same syntax found for wg(8), and a more complete description may be found there. Bold lines below are for options that extend wg(8).
The following might be used for connecting as a client to a VPN gateway for tunneling all traffic:


Address =


PrivateKey = oK56DE9Ue9zK76rAc8pBl6opph+1v36lm7cXXsQKrQM=


PublicKey = GtL7fZc/bLnqZldpVofMCD6hDjrK28SsdLxevJ+qtKU=

PresharedKey = /UwcSPg38hW/D9Y3tcS1FOV0K1wuURMbS0sesJEP5ak=

AllowedIPs =

Endpoint =
The `Address` field is added here in order to set up the address for the interface. The `DNS` field indicates that a DNS server for the interface should be configured via resolvconf(8). The peer's allowed IPs entry implies that this interface should be configured as the default gateway, which this script does.
Building on the last example, one might attempt the so-called ``kill-switch'', in order to prevent the flow of unencrypted packets through the non-WireGuard interfaces, by adding the following two lines `PostUp` and `PreDown` lines to the `[Interface]` section:

PostUp = iptables -I OUTPUT ! -o %i -m mark ! --mark $(wg show %i fwmark) -j REJECT

PreDown = iptables -D OUTPUT ! -o %i -m mark ! --mark $(wg show %i fwmark) -j REJECT
The `PostUp' and `PreDown' fields have been added to specify an iptables(8) command which, when used with interfaces that have a peer that specifies as part of the `AllowedIPs', works together with wg-quick's fwmark usage in order to drop all packets that are either not coming out of the tunnel encrypted or not going through the tunnel itself. (Note that this continues to allow most DHCP traffic through, since most DHCP clients make use of PF_PACKET sockets, which bypass Netfilter.)
Or, perhaps it is desirable to store private keys in encrypted form, such as through use of pass(1):

PostUp = wg set %i private-key <(pass WireGuard/private-keys/%i)
For use on a server, the following is a more complicated example involving multiple peers:


Address =

Address =

SaveConfig = true

PrivateKey = yAnz5TF+lXXJte14tji3zlMNq+hd2rYUIgJBgB3fBmk=

ListenPort = 51820


PublicKey = xTIBA5rboUvnH4htodjb6e697QjLERt1NAB4mZqp8Dg=

AllowedIPs =,


PublicKey = TrMvSoP4jYQlY6RIzBgbssQqY3vxI2Pi+y71lOWWXX0=

AllowedIPs =,


PublicKey = gN65BkIKy1eCE9pP1wdc8ROUtkHLF2PfAqYdyYBz6EA=

AllowedIPs =
Notice the two `Address' lines at the top, and that `SaveConfig' is set to `true', indicating that the configuration file should be saved on shutdown using the current status of the interface.
These configuration files may be placed in any directory, putting the desired interface name in the filename:
# wg-quick up /path/to/wgnet0.conf
For convienence, if only an interface name is supplied, it automatically chooses a path in `/etc/wireguard/':
# wg-quick up wgnet0
This will load the configuration file `/etc/wireguard/wgnet0.conf'.


wg(8), ip(8), ip-link(8), ip-address(8), ip-route(8), ip-rule(8), resolvconf(8).


wg-quick was written by Jason A. Donenfeld For updates and more information, a project page is available on the World Wide Web
2016 January 1 ZX2C4